It provides a reliable replacement for your vehicle’s engine block heater cord, ensuring your Cummins Diesel engine stays warm in cold weather, aiding in easier starting and reducing wear on the engine. Installation Instructions: Park your Ram 2500 or 3500 on a level surface and turn off the engine. Locate the existing engine block heater cord on your vehicle, typically connected to the front of the engine. Unplug the old cord from the engine block heater element. Follow the existing cord to its connection point, which is often near the front grille or under the hood. Disconnect the old cord from its power source or outlet. Route the new Genuine OEM cord along the same path as the old one, ensuring it is secured in place and not in contact with moving parts or hot components. Plug the new cord into the engine block heater element. Connect the other end of the cord to the power source or outlet used for engine block heating. Ensure all connections are secure and free from damage. The installation process typically takes 15-30 minutes and can be performed by individuals with basic automotive maintenance skills. Park your Ram 2500 or 3500 on a level surface and turn off the engine. Connect the other end of the cord to the power source or outlet uséd for engine block heating. Sorry, our items are NOT available for pick-up. No additional information at this time. You might also like.
Turbo Model H1E-8294AX/FA22SA8, H1E. Displacement 8.3L, 8300 ccm. 3527107 3527123, 352712300, 352712300H, 3527123H, 3527123NX. 3527123RX, 3528789, 3528790, 3528790NX, 3528790RX, 3530773. 3530773NX, 3530773RX 3802257, 3802257NX, 3802257RX, 3927723. The installation steps of the turbocharger are as follows. Step 1 : Before Replacing A Turbo. It is important to conduct a thorough diagnostic check of the engine system to determine if the “fault” is actually the turbocharger. If the engine diagnostic check does not uncover any obvious cause, make sure that an extensive trouble shooting analysis is completed. Step 2 : Turbo Installation. Check the part number to ensure that it is the right one for the engine. If in doubt, check with us. It is important that during the whole installation process, you prevent dirt or debris from entering any part of the turbo. Ensure that correct gaskets are used. Important Note: Do not use liquid gasket or sealants, particularly for the oil inlet or outlet since excessive material may enter the turbo, reducing or stopping oil flow. It is recommended that you use new air, oil and fuel filters and clean engine oil to the engine or vehicle maker’s specification. Before installing the turbo, ensure that all air hoses connected to the turbo are totally clean and show no sign of any damage. The air filter and its housing must be completely clean and free from any debris. Clean the engine breather system and ensure that it functions properly. Remove any old gasket material from the exhaust manifold and pipe. The surfaces of the flange must be clean and have no damage. Position the turbo onto manifold or engine block using the correct new gasket or O ring, and then reconnect the exhaust pipe. Tighten all nuts and bolts. Next, install oil drain line to the turbocharger. We recommend fitting a new oil inlet pipe when installing the new turbo. Pour new engine oil into the oil inlet hole of the turbocharger. Next, fit the new oil feed line. Install inlet and outlet air hoses to turbocharger compressor housing. Make sure that the connections are airtight and hose clamps are correctly tightened. 2.14 Crank the engine for 10 – 15 seconds without starting the engine. If possible, disable the fuelling/ignition or use compressiontest mode to allow this. This helps to prime the oil feed to the turbocharger by filling the oil pressure lines, oil filter and turbo with oil before start-up. Important note: as soon as the engine starts, the turbo willrun at high speed and a lack of lubrication in these vital first few seconds can destroy a brand new turbo. Then start the engine, and let it idle for 3 to 4 minutes to allow for proper inspection of oil, gas and airleakage. Stop the engine and re-check engine oil level. Oil level should be between the minimum and maximum mark on the dipstick. It is important to make surethat oil level is not above the point where turbo oil drain pipe connects to the engine. Or this may lead to oil leakage from the turbo into the inlet and exhaust systems. Engine:Cummins 6CT, 6CTA. As the picture shows. OE Spec or Performance/Custom. Please Add Engine Oil Before Use. Set_id=880000500F’ center center / 100% auto no-repeat; #product1_83425ac01be95eeefdf29b2cbe83292e. Image{width: 100%;} #product1_83425ac01be95eeefdf29b2cbe83292e. Title{margin: auto; width: 85%; font-size:11px; font-family: Arial; line-height: 12px; text-decoration: none; display: block; height: 2em; overflow: hidden; text-align: center; color : #191919; padding-top: 4px;} #product1_83425ac01be95eeefdf29b2cbe83292e. Title:before{content:’Front Bumper Tow Hook License Plate Bracket For Bmw E60 E63 645I 535I Z4 3/5/6/7′;} #product1_83425ac01be95eeefdf29b2cbe83292e. Item-id{font-size:11px; line-height: 12px; text-decoration: none; display: block; overflow: hidden; color : #191919} #product1_83425ac01be95eeefdf29b2cbe83292e. Item-id:before{content:’273921089094′;} #product1_83425ac01be95eeefdf29b2cbe83292e. Price{display: block; color : #bf0000; padding: 10px 0 4px; text-align: center; font-size: 16px; font-family: Arial; font-weight: 600; -webkit-text-size-adjust:none; text-decoration:none;} #product1_83425ac01be95eeefdf29b2cbe83292e. Price:before{content:’USD 13.95′;} #product1_83425ac01be95eeefdf29b2cbe83292e. Set_id=880000500F’ center center / 100% auto no-repeat; #product2_83425ac01be95eeefdf29b2cbe83292e. Image{width: 100%;} #product2_83425ac01be95eeefdf29b2cbe83292e. Title{margin: auto; width: 85%; font-size:11px; font-family: Arial; line-height: 12px; text-decoration: none; display: block; height: 2em; overflow: hidden; text-align: center; color : #191919; padding-top: 4px;} #product2_83425ac01be95eeefdf29b2cbe83292e. Title:before content:’For Chevy SBC 350 327 383 400 Mechanical Fuel Pump 3/8\\.
QSB4.5 Cylinder Head Assy For Cummins diesel engine parts. QSB4.5 Cylinder Head Assy. Note: Please Send more information like model number, serial number, engine number, pictures, size. Pictures in different views For your old Part. We wil confirm much quicker. 1 PCS Cylinder Head Assy. We will be happy to assist you and resolve any concerns you may have. Orders are processed from Monday to Saturday, excluding legal holidays. The item must also have the attached tags and wrap intact. Otherwise, the sale is considered final. We will be happy to work with you in a friendly and cordial manner to resolve any problems you may have. Please make sure your address and contact information are correct. All original manufactories name, Part No. Logo, Package and Description for reference purproses only.
